HAL default configuration file. More...

#include "stm32yyxx_hal_conf.h"
#include "stm32wb0x_hal_adc.h"
#include "stm32wb0x_hal_crc.h"
#include "stm32wb0x_hal_i2c.h"
#include "stm32wb0x_hal_pwr.h"
#include "stm32wb0x_hal_spi.h"
#include "stm32wb0x_hal_tim.h"
#include "stm32wb0x_hal_uart.h"

Macros
#define	USE_HAL_ADC_REGISTER_CALLBACKS 0u
	Include the default list of modules to be used in the HAL driver and manage module deactivation.

#define	USE_HAL_I2C_REGISTER_CALLBACKS 0u

#define	USE_HAL_IRDA_REGISTER_CALLBACKS 0u

#define	USE_HAL_PKA_REGISTER_CALLBACKS 0u

#define	USE_HAL_RNG_REGISTER_CALLBACKS 0u

#define	USE_HAL_RTC_REGISTER_CALLBACKS 0u

#define	USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0u

#define	USE_HAL_SMBUS_REGISTER_CALLBACKS 0u

#define	USE_HAL_SPI_REGISTER_CALLBACKS 0u

#define	USE_HAL_TIM_REGISTER_CALLBACKS 0u

#define	USE_HAL_UART_REGISTER_CALLBACKS 0u

#define	USE_HAL_USART_REGISTER_CALLBACKS 0u

#define	HSE_VALUE (32000000UL)
	Adjust the value of External High Speed oscillator (HSE) used in your application.

#define	HSE_STARTUP_TIMEOUT (100UL)

#define	HSI_VALUE (64000000UL)
	Internal High Speed oscillator (HSI) value.

#define	LSI_VALUE (32000UL)
	Internal Low Speed oscillator (LSI) value.

#define	LSE_VALUE (32768UL)
	External Low Speed oscillator (LSE) value.

#define	RC64MPLL_VALUE (64000000UL)
	64 MHz PLL clock default value.

#define	LSE_STARTUP_TIMEOUT (5000UL)

#define	LSE_DRIVE_LEVEL RCC_LSEDRIVE_MEDIUMLOW

#define	VDD_VALUE (3300UL)
	This is the HAL system configuration section.

#define	TICK_INT_PRIORITY ((1UL<<__NVIC_PRIO_BITS) - 1UL)

#define	USE_RTOS 0U

#define	USE_SPI_CRC 1U
	Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code.

#define	CFG_HW_RCC_HSE_CAPACITOR_TUNE 32
	Default value of the HSE capacitor tuning.

#define	CFG_NUM_RADIO_TASKS (1)
	This is the BLE number of link configuration section Maximum number of simultaneous radio tasks.

#define	USE_RADIO_PROPRIETARY_DRIVER 1U
	This macro must be set to 0 when BLE stack is used.

#define	assert_param(expr) ((void)0U)
	Include module's header file.

Detailed Description

HAL default configuration file.

Attention

This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.

Macro Definition Documentation

◆ CFG_NUM_RADIO_TASKS

#define CFG_NUM_RADIO_TASKS (1)

This is the BLE number of link configuration section Maximum number of simultaneous radio tasks.

Radio controller supports up to 128 simultaneous radio tasks, but actual usable max value depends on the available RAM.

◆ HSE_STARTUP_TIMEOUT

#define HSE_STARTUP_TIMEOUT (100UL)

Time out for HSE start up, in ms

◆ HSE_VALUE

#define HSE_VALUE (32000000UL)

Adjust the value of External High Speed oscillator (HSE) used in your application.

This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL). Value of the External oscillator in Hz

◆ HSI_VALUE

#define HSI_VALUE (64000000UL)

Internal High Speed oscillator (HSI) value.

This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL). Value of the Internal oscillator in Hz

◆ LSE_DRIVE_LEVEL

#define LSE_DRIVE_LEVEL RCC_LSEDRIVE_MEDIUMLOW

Drive level for LSE oscillator.

◆ LSE_STARTUP_TIMEOUT

#define LSE_STARTUP_TIMEOUT (5000UL)

Time out for LSE start up, in ms

◆ LSE_VALUE

#define LSE_VALUE (32768UL)

External Low Speed oscillator (LSE) value.

< Value of the Internal Low Speed oscillator in Hz The real value may vary depending on the variations in voltage and temperature. This value is used by the UART, RTC HAL module to compute the system frequency Value of the External oscillator in Hz

◆ LSI_VALUE

#define LSI_VALUE (32000UL)

Internal Low Speed oscillator (LSI) value.

LSI Typical Value in Hz

◆ RC64MPLL_VALUE

#define RC64MPLL_VALUE (64000000UL)

64 MHz PLL clock default value.

This value is the default RC64M_PLL value after Reset. Value of the Internal oscillator in Hz

◆ TICK_INT_PRIORITY

#define TICK_INT_PRIORITY ((1UL<<__NVIC_PRIO_BITS) - 1UL)

tick interrupt priority (lowest by default)

◆ USE_RADIO_PROPRIETARY_DRIVER

#define USE_RADIO_PROPRIETARY_DRIVER 1U

This macro must be set to 0 when BLE stack is used.

Set to 1 to use radio proprietary protocol with action packets.

◆ VDD_VALUE

#define VDD_VALUE (3300UL)

This is the HAL system configuration section.

Value of VDD in mv

Macros